![Ocean iPhone Repair (by Appointment Only)](/img/default-banner.jpg)
- 31
- 121 410
Ocean iPhone Repair (by Appointment Only)
United States
Приєднався 18 сер 2016
Ocean iPhone Repair
Servicing the Bay Area since 2009!
www.oceaniphonerepair.com
Servicing the Bay Area since 2009!
www.oceaniphonerepair.com
Focusrite Audio Interface No Audio Motherboard Repair
Focusrite had no audio input or output. Opened device and found a short circuit with one component using my thermal camera. I removed the bad component and tested the device with the component removed and the other audio jack worked. The shorted component was causing both input jacks to stop working.
I ordered a new replacement component from eBay and replaced it a few weeks later and all is working again.
I ordered a new replacement component from eBay and replaced it a few weeks later and all is working again.
Переглядів: 326
Відео
2014 macbook air no backlight repair
Переглядів 373 місяці тому
2014 macbook air no backlight liquid spill repair
BMW crank no start error 006292, 006293 fuel pump controller repair. No programming, cost me $15
Переглядів 1,7 тис.3 місяці тому
2011 BMW 328i died on the freeway after hard acceleration. Car still had battery power but engine shut off. Took about 30 minutes until car would start again after multiple tries. Second time happened again about a week later on the freeway driving 65 mph. After 30 minutes I was able to start it again. Both times the car shut off I was about 45 minutes to an hour driving before it happened. Aft...
iPhone 11 Pro no display motherboard repair
Переглядів 407Рік тому
iPhone 11 Pro / 11 pro max no display or display shows all different colors usually is due to burned or damaged display filter on the motherboard.
PlayStation 5 HDMI connector replacement
Переглядів 443Рік тому
PlayStation 5 HDMI replacement. Seems the PS5 HDMI connectors are made to fail. Every single one Ive repaired all have little to no solder on all the pads.
iPhone X - No cellular signal motherboard repair
Переглядів 1,8 тис.Рік тому
iPhone X - No cellular signal motherboard repair
iphone 7 audio ic repair without removing IC chip
Переглядів 3792 роки тому
iphone 7 audio ic repair without removing IC chip
iPhone not charging, possible lint build up
Переглядів 413 роки тому
iPhone not charging, possible lint build up
usb flash drive 4 pin connector repair
Переглядів 1453 роки тому
usb flash drive 4 pin connector repair
iphone 12 no power motherboard repair for data recovery
Переглядів 2993 роки тому
iphone 12 no power motherboard repair for data recovery
2011 BMW 328i (no nav) eonon GA 7165 stereo upgrade deletes factory chime noise. How to fix?
Переглядів 4,7 тис.7 років тому
2011 BMW 328i (no nav) eonon GA 7165 stereo upgrade deletes factory chime noise. How to fix?
Nexus 5 power button repair - boot loop fix
Переглядів 45 тис.7 років тому
Nexus 5 power button repair - boot loop fix
iPhone 6 / 6 plus - iPhone aftermarket LCD screen vs OEM LCD screen
Переглядів 56 тис.7 років тому
iPhone 6 / 6 plus - iPhone aftermarket LCD screen vs OEM LCD screen
iPhone 6 Plus Screen Repair in 5 Minutes
Переглядів 1758 років тому
iPhone 6 Plus Screen Repair in 5 Minutes
Very impressive. Do you normally do just one jumper?
Yes only one jumper is needed. I’ve never had issues with the other two jumpers doing it this way and have never had any baseband issues either.
Nice job man, very cleanly done.
U sure it’s living?
I guess you could say you found a bug in your computer I'll let myself out
wait for me
that spider aint living, mf dead 😂
Hey did you figure anything out yet? I have the same issue. Bought the car like that and I want the factory BMW chime.
Unfortunately no. I still have the same beeping noise lol. I bought a “LC-BMRC-01 METRA AXXESS / 2006 -20015 BMW / MINI RADIO INTERFACE HARNESS W/CHIME” but was unable to figure out who to connect it to this stereo.
good job
Which Kapton tape do you use? What thickness ans which mfgr?
Hey Roy - Thx a mill for this excellant video! Followed it by the letter and got it on the first go. And I'm a beginner and never done hot air soldering before. Kapton tape is a lifesaver!
What kind of tape you used to protect the board?
Kapton tape
what is the size of that button? is it the 4mm or 5mm power button?
so Refurbished is the OEM?
What is that transparent yellow tape all about? Is it heat-conductive? Captain's tape? Can't find it in Google... I tried using aluminum foil.
i notice the difference between the two but I'm just like that, the refresh rate is slightly lower I notice a little light drag when you are swiping across the home screen and the overall tint of the screen is on the more cooler blue side than the original screens. Some people don't mind but I'm just a never satisfied perfectionist
True
Trueee. What I did was go to color filter settings and change the tint back so it looks less blue
Great Video On iPhone Repair. It's nice to see a good POV to further my knowledge
nice work
Did you ever compare battery life with aftermarket vs original screen? I know the really bad aftermarkets drain battery like crazy, but what about a good aftermarket vs original
some after market ones the brightness isnt good its not the same as the oem which im talking about stright from factory from apple quality
have you used NCC screens from Bizbee? Their brightness is very close to the original and the price is only half of the OEM. www.bizbee.com/A10768.html
So did Eonon provide you with a fix? I have the same "issue"
Ocean iPhone Repair (by Appointment Only) Thanks tho, I might blow another $65 on that stupid chime :) How sure are you that Axxess wiring interface will work? I checked the website and it fits my specific car model. My concern is that it will fix the chime but mess up something else.
Any update on this? Did anyone sort the chime? That ugly beep is so annoying!
Hey where are you purchasing JDF screens? I've seen them on ETrade Supply but their shipping costs are outrageous
Codeman785 I switched to Tianma mid 2017. Parts are from vendors in Los Angeles
Ocean iPhone Repair (by Appointment Only) ok how well do you think the quality is compared to Jdf?
Codeman785 I like it much better. I believe at some point other brands were tweaking the brightness level on their lcds which would end up causing a short and the lcd would randomly go black. This was the main reason I switched.
Roy r ok, that will be the next one I will buy. What exact website do you get them from? Is it Alixpress?
Roy r Hey could you please tell me what website you use to get those screens? I'm going to need more soon.
But I thought the problem was due to some soldering issue at the chip end. This info is all over internet if you google for Nexus bootloop issue.
Hi thanks for the video. I was wondering what temperature are you soldering at? Also what temperature are you desoldering at when using the wick?I'm having trouble melting solder with the smd hot air gun went as high as 470 Celsius.
Hi, 380 should be good enough but not all units are the same. I usually set mine 380-420 because I know my burning point already. You can put some flux to help desolder the old button. Make sure your iron is clean. You can use a damp sponge to clean your iron while it is hot.
"sodder"
Thank you very much for sharing. Can you please tell me what flux you use?
so if its OEM grade it shouldnt have any issues
Spray the perfume on the button POWER and blow dry
vitalik kobrin You're a goddamn genius! Totally worked hahahaha thanks!
Doesn't work if the button is really broken
do you guys sell the oem screens or do you only do repairs?
Michael B. Hi, we only do the repairs.
If you want touchID u have to keep your old home button.
Been reading all your comments with Tez or whatever.. I just installed mine last night and love it!! Big learning curve though definitely has some kinks. I'm going to do a video basic tour next week. Dunno how to fix the chimes unless somehow you take something out of the old can bus thing and put it in this can bus thing? Might be software related which = very difficult.. I'll let you know if I find anything.. One question. The talk button on the steering wheel mutes it, I was hoping I could make that the speech recognition.. let me know if you know a fix!
ill do some tests with the talk button on the steering wheel today and find out. I haven't really tested that part yet. I just fixed all the issues I was having (except chime) yesterday by updating software to the Volkswagen version then back to the E90 and it fixed my radio reset issue so I'm super happy with the unit now. I was about to return it but now that its fixed I'm super happy with this unit! just curious what version is your unit right now? mine is @ MCU last 6 digits: 170508 System version: V7.3.1_20170505.100912_KBT
How much does it cost such procedures in the shop?
Thanks bro
Thankx for sharing, how many degrees are you setting the heater pipe..please???
Jose Torrano I believe my rework station is set at 420F. I use that for most applications because I'm already used to it and I know my burning point.
Hello, Sir/Madam! Please kindly write and tell us your order NO., serial NO. or the email address used when placing the order. You can also contact with us with the email address support@eonon.com. We will do our best to help you. Thanks!
Hello, Sir/Madam! Did you solve the problem of your head unit? If not, please kindly write and tell us your order NO., serial NO. or the email address used when placing the order. You can also contact with us with the email address support@eonon.com. We will do our best to help you. Thanks!
Which is better if I'll replace my screen? hope you're gonna answer. Oem or aftermarket?
because my screen has a lot of crack especially on the camera there's a crack in there
Cecilia Marbas both are a good option but it depends where you get the screen repaired. I have seen my fair share of really bad aftermarket and OEM screen floating around and a lot of vendors actually market their aftermarket as OEM. Research is key. Look for reviews on the shop you decide on and ask about their warranty, what it covers and the length of their warranty. You want something 6 months or longer. I have seen some OEM and aftermarket screens that start to show signs of defect after a 3-4 month period so you want to stay away from shops with a guarantee less then 6 months.
Ocean iPhone Repair (by Appointment Only) i have got my phone repaired twice at the same location and the screen doesnt seem calibrated its really hard to type.. should i just try to get a refund and replace elsewhere?
maybe call them and ask about their warranty replacement. if you have the iPhone 6 plus then it could be a touch IC problem and not the screen. but call the place you had it repaired and let them know the situation and hopefully try getting it replaced a third time if its covered under warranty, which it should be.
Actually, some aftermarket screens are pretty good. Their quality is very close to the original, while the price is the half of the OEM. If you are still searching for some high-quality screens, I recommend screens from Bizbee. www.bizbee.com/
Hi I was wondering where you buy your JDF screens?
Same here! I can't find them anywhere!
Why did you use wick to remove the solder from the pads just to add solder back on?
Tuoli factory here, if you want refurbish material, welcome to contact sunny get know more details. whatsapp:+008613538033801, email:Sunny@tuolitech.com
Great video, thx for this 1
Good idea Roy, you're absolutely right, it's about helping others. I will have zero special tools, it will be my first repair of this type and look forward to the challenge. I'm surprised at how many people have glass so totally cracked they can hardly see the screen. Thanks for the suggestion.
T Rose
So don't do it yourself, we need you. How about you need us to make money so let's make it look like we can't do it...
By all means, do it yourself, no one is stoping you.
I plan to. I've fixed computers, jets in Nam, cars, boats, TV's, the list is too long. ....
Oh, and by the way, there's two p's in stopping.
T Rose awesome! It would be great if you could upload your own video of the repair to help contribute to the community here as well. That's what these videos are uploaded for, to help others.
Does it really matter which one you use to replace?
Phuoc Tran i hope he answers, I really wanna know too. I broke my phone and I'm going to repace it.
preference wise, if you can get passed the slight differences mentioned in the video then no, it does not matter.
OEM fits better, my aftermarket gives out light on the side.
Ocean iPhone Repair (by Appointment Only) I does matter. Touch is not accurate. I replaced few days ago for $25 and I didn't like the touch experience.slippery touch. Like when you charge with copy charger and phone act weird and very slippery but with mine it act less slippery but my confidence of touch is gone now
Christine Alexis Villanueva and my wife broke my phone
Thanks a lot dear brother , you are wonderful 🌹 Keep going 👍
Cool, what's the name of the after market brand?
Emad Oqdi jdf
there are different brands: Tianma, Longteng, Jingdongfang, Shenchao